Menvier Security TS790+ Specifikace Strana 21
- Strana / 70
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
TS790+ & TS900+ Installation Manual System Installation
Auxiliary Tamper
These two terminals provide tamper protection
to auxiliary devices such as power supplies,
extension loudspeakers etc. If they are not used
they must be linked out.
Extension Loudspeakers
Up to two extension loudspeakers can be
connected across the [SPK+] and [H/O-]
terminals on the control panel PCB. The volume
for the loudspeaker is controlled by VR1
“Speaker Volume”.
Figure 18. Loudspeaker Connections
Digicom/RedCARE Installation
Connect a digital communicator, RedCARE STU
or Paknet interface card to the control panel
using the following connections:
These are the programmable digicom output
connections. They are normally at +12V and
switch to 0V when active. The outputs can be
inverted so that they switch from 0V to +12V
when active (see System Configuration on
page 34 ). Each output will source 5mA in the
+12V condition and sink 100mA in the 0V
condition.
Alternatively, fit a plug-on STU to JP9 and JP10.
This uses Digicom outputs 1 to 7 for Channels 1
to 7. Note that Channel 8 on this interface is
dedicated to “Low Battery”. You
remove
the "CS" link at JP7 before fitting a plug-on STU to
ensure correct operation of Remote Reset via
RedCARE.
This provides the +12V power to the digicom.
This output is un-fused and therefore should only
be used if the digicom is fitted inside the control
panel. Use any of the auxiliary 0V terminals for
the 0V supply for the digicom/STU.
If an external device switches this input to +12V,
the control unit generates a “Line Fault”. If a
“Line Fault” occurs while the system is unset then
the control unit generates a “Chime”every
minute. If a “Line Fault” occurs while the system
is set then the control unit cancels the “Bell
Delay”.
Figure 19. 3GSTU RedCARE Connections
Plug-on Digicom Installation
A plug-on digital communicator DC54 or DC58
may be fitted inside the control panel to allow
alarm status information to be transferred to a
dedicated central station. The unit should be
fitted in accordance with the installation
instructions supplied with it and connected to
the control panel plug DIGI-MODEM (JP3) using
the lead provided with the unit, see Figure 20.
The NVM within the digicom can either be
programmed via the control panel, see page
52. or directly using an engineer's keypad
plugged into the digimodem.
- TS790+ & TS900+ 1
- Contents 3
- Overview 5
- TSXNODE 6
- TS900 NODE (Obsolete) 6
- ID Node (TS900 IDNODE) 6
- TS700 LEC 6
- Specifications 7
- System Installation 8
- Remote Network Wiring 9
- Control Panel Installation 10
- Control Panel PCB Layout 11
- Mains Connection 13
- Battery Connection 13
- Remote Keypads 13
- Installation Procedure 14
- Engineer’s Keypad 15
- XNode (TS900+) 15
- A B C D E 16
- TS900 Node Layout (Obsolete) 17
- TS700 LEC Installation 18
- Wiring Detection Circuits 18
- External Sounder Connections 19
- Program circuit 20
- Auxiliary Tamper 21
- Extension Loudspeakers 21
- Digicom/RedCARE Installation 21
- Plug-on Digicom Installation 21
- Connecting a Printer 22
- Programmable Outputs 24
- Pre Power-Up Checks 25
- Initial Power-Up 25
- Power-Up Checks 26
- NVM Defaults 26
- Engineer’s Menu 1 28
- Panel Outputs [1.1] 29
- Digicom Outputs [1.2] 29
- Digicom Channels [1.3] 29
- Programmable Output Types 29
- Program Circuits [1.4] 32
- Circuit Attributes 33
- System Timers [1.5] 34
- Setting Modes [1.6] 37
- Do System Print [1.7] 38
- Configuration [1.9] 38
- Goto User Menu 1 [1.0] 41
- Relearn Hardware [1.C] 42
- Engineers Menu 2 43
- View Circuits [2.1] 44
- Set System Time [2.2] 44
- Set System Date [2.3] 44
- Change Passcode [2.4] 44
- Chime Circuits [2.5] 45
- Alter 24Hr Group [2.6] 45
- Print System Log [2.7] 45
- Configure Wards [2.8] 45
- View System Log [2.9] 46
- Log Event Codes 47
- Reset User Code 1 [2.0] 48
- Start Call Back [2.A] 48
- Engineer’s Menu 3 49
- Time Switches [3.1] 50
- Part Set Groups [3.2] 51
- Code Set Groups [3.3] 51
- Reset Message 52
- Banner Message 52
- XNode Outputs [3.8] 53
- Built In Tests [3.9] 53
- Voltage 54
- Test Digi Outputs 54
- Custom Output - Example 1 55
- Custom Output - Example 2 55
- Custom Output - Example 3 55
- Modem Password Flowchart 56
- Modem site Number Flowchart 56
- Program Digi Flowchart 57
- Reset Digicom 58
- Appendices 59
- Ward(s) 62
- Alarm Abort Operation 65
- Text Editing Keys 66
- Setup New Users 66
- Setup New Users Flowchart 67
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Menvier Security TS790+
(12 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce