Menvier Security TS790+ Specifikace Strana 15
- Strana / 70
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
TS790+ & TS900+ Installation Manual System Installation
as normal. When the link is set to the
enabled position the sounder is only
enabled when the remote keypad
programmable output is active. For
example, to make the keypad ward
respective for ward A, program the output
on the remote keypad to "Sounder Control
A" (type 064) and set the "Ward Sounder
Control" link to the enabled position. (Hint:
use Engineer Menu 1 option 1. Panel o/p 5
= keypad o/p 1, panel o/p = keypad o/p 2
and so on.)
7. Finally clip the remote keypad cover onto
the base being careful not to trap any
cables or to obstruct the tamper switch.
Engineer’s Keypad
Normally all system programming will be carried
out from one of the installed remote keypads,
however sometimes it may be more convenient
to program the system at the control panel. This
can be achieved by using an “Engineers
Keypad” which is temporarily plugged on to the
control panel (JP2).
DO NOT plug the Engineer’s Keypad into JP1
or you may damage the equipment.
To convert a standard remote keypad to an
“Engineers Keypad” an Engineer’s interface lead
is required which can be obtained from your
supplier (P/No. NETEKI).
Figure 10. Engineer’s Keypad Connections
XNode (TS900+)
The XNode is very similar to the TS900 Node in
that it provides the facility to add an extra eight
programmable detection circuits and two
programmable outputs. The maximum number
of XNodes that can be connected to any one
network is 5.
XNode Wiring
The XNode requires a 4 core cable for
interconnection, and up to 5 may be
connected in a “daisy-chain” or “star”
configuration. The distance between each
XNode must not exceed 100 metres. The total
distance to last XNode must not exceed 500
metres. The Aux. +/- terminals provide power for
the detectors.
Programmable Outputs on the XNode
The XNode has two programmable outputs,
each rated at 100mA, output [A+] is a switched
+ve output and output [B-] is a switched -ve.
The outputs can be used to drive sounders or
relays etc.
- TS790+ & TS900+ 1
- Contents 3
- Overview 5
- TSXNODE 6
- TS900 NODE (Obsolete) 6
- ID Node (TS900 IDNODE) 6
- TS700 LEC 6
- Specifications 7
- System Installation 8
- Remote Network Wiring 9
- Control Panel Installation 10
- Control Panel PCB Layout 11
- Mains Connection 13
- Battery Connection 13
- Remote Keypads 13
- Installation Procedure 14
- Engineer’s Keypad 15
- XNode (TS900+) 15
- A B C D E 16
- TS900 Node Layout (Obsolete) 17
- TS700 LEC Installation 18
- Wiring Detection Circuits 18
- External Sounder Connections 19
- Program circuit 20
- Auxiliary Tamper 21
- Extension Loudspeakers 21
- Digicom/RedCARE Installation 21
- Plug-on Digicom Installation 21
- Connecting a Printer 22
- Programmable Outputs 24
- Pre Power-Up Checks 25
- Initial Power-Up 25
- Power-Up Checks 26
- NVM Defaults 26
- Engineer’s Menu 1 28
- Panel Outputs [1.1] 29
- Digicom Outputs [1.2] 29
- Digicom Channels [1.3] 29
- Programmable Output Types 29
- Program Circuits [1.4] 32
- Circuit Attributes 33
- System Timers [1.5] 34
- Setting Modes [1.6] 37
- Do System Print [1.7] 38
- Configuration [1.9] 38
- Goto User Menu 1 [1.0] 41
- Relearn Hardware [1.C] 42
- Engineers Menu 2 43
- View Circuits [2.1] 44
- Set System Time [2.2] 44
- Set System Date [2.3] 44
- Change Passcode [2.4] 44
- Chime Circuits [2.5] 45
- Alter 24Hr Group [2.6] 45
- Print System Log [2.7] 45
- Configure Wards [2.8] 45
- View System Log [2.9] 46
- Log Event Codes 47
- Reset User Code 1 [2.0] 48
- Start Call Back [2.A] 48
- Engineer’s Menu 3 49
- Time Switches [3.1] 50
- Part Set Groups [3.2] 51
- Code Set Groups [3.3] 51
- Reset Message 52
- Banner Message 52
- XNode Outputs [3.8] 53
- Built In Tests [3.9] 53
- Voltage 54
- Test Digi Outputs 54
- Custom Output - Example 1 55
- Custom Output - Example 2 55
- Custom Output - Example 3 55
- Modem Password Flowchart 56
- Modem site Number Flowchart 56
- Program Digi Flowchart 57
- Reset Digicom 58
- Appendices 59
- Ward(s) 62
- Alarm Abort Operation 65
- Text Editing Keys 66
- Setup New Users 66
- Setup New Users Flowchart 67
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Menvier Security TS790+
(12 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.724 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce