Menvier Security TS900+ Specifikace Strana 12
- Strana / 68
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Mains Connection
The mains supply is connected to a 3 way "Euro
Type" fused terminal block, which is fitted with a
315mA fuse. All electrical connections should be
carried out by a qualified electrician and must
comply with the current IEE regulations.
To comply with european regulations the
supply should be fed from a readily
accessible disconnect device, e.g.
un-switched fused spur fitted.
When making mains connections it should
be ensured that if the cable slips in such a
way as to place a strain on the conductors,
the protective earthing conductor will be
the last to take the strain.
Battery Connection
A 7Ah battery must be fitted to the system to allow
it to function during a mains fail condition. The
TS790/TS900 is equipped with a “Battery Protection”
circuit so that if a battery is accidentally reverse
connected or its voltage is below 4V, the “Battery
Fault” LED illuminates. To clear the fault simply
reconnect or replace the battery as appropriate.
Remote Keypads
Four types of remote keypads can be used on the
system, however, only the TS900 remote keypad
can be used for programming text information.
Any combination of remote keypad may be used
on the same system if desired.
NETLCD Remote Keypad
The NETLCD remote keypad has a 32 character
backlit Liquid Crystal Display (LCD)
NETSTAR Remote Keypad
The NETSTAR remote keypad has a 8 character
backlit Starburst Liquid Crystal Display (LCD).
NETLED Remote Keypad
The NETLED remote keypad has a 4 character LED
display.
NETARM Remote Arming Station
The NETARM remote arming station does not have
a display, therefore it is designed to only be used
where setting, part setting and unsetting of the
system is required.
PCB Layouts & Connections
Detection Circuits.
Each remote keypad has two
programmable detection circuits.
Loudspeaker Volume.
For adjusting the volume of a speaker wired
to the remote keypad (NETLCD only).
LED Mimic.
If this jumper link is set to the “enabled”
position, the red () LED on the keypad will
be “ON” when the keypad output is active.
Remote I/D.
Used to select the remote keypads address.
(ENG = Engineer).
Ward Sounder Control.
If this jumper link is set to the “disabled”
position, the remote keypad sounder will
follow the control panel speaker output. If
this link is set to “enabled”, the remote
keypad sounder will only activate when the
panel speaker and the output on the
remote keypad are active at the same time.
Loudspeaker Output.
This terminal can be connected to a single
16 Ω Loudspeaker (NETLCD only).
Network Connections & O/P.
Terminals A to E are used to connect the
remote keypad to the control panel
network. The O/P terminal is the
programmable output.
8
System Installation TS790 & TS900 Installation Manual
L
E
N
To transformer
FUSE 315mA
Figure 7. Mains Supply Connections
- TS790 & TS900 1
- Overview 3
- System Installation 3
- Engineer’s Menu 1 3
- Engineer's Menu 2 3
- Engineers Menu 3 4
- Appendices 4
- System Architecture 5
- Control Panel 5
- Remote Keypads 6
- TS900 NODE 6
- ID Node (TS900.IDNODE) 6
- TS700 LEC 6
- Specifications 6
- Cable Routing 7
- Remote Network Wiring 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- NETLCD Remote Keypad 12
- NETSTAR Remote Keypad 12
- NETLED Remote Keypad 12
- NETARM Remote Arming Station 12
- PCB Layouts & Connections 12
- Tamper Switch 13
- ENT Key Disable 13
- Engineer’s Keypad 14
- Figure 11. TS900 Node Layout 15
- TS700 LEC Installation 16
- Wiring Detection Circuits 16
- External Sounder Connections 17
- Auxiliary Tamper 18
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 19
- Plug-on Digicom Installation 19
- Connecting a Printer 20
- Programmable Outputs 21
- Pre Power-Up Checks 22
- Initial Power-Up 22
- Power-Up Checks 23
- NVM Defaults 23
- Introduction 25
- Panel Outputs 26
- Digicom Outputs 26
- Digicom Channels 26
- Programmable Output Types 26
- Program Circuits 29
- Circuit Attributes 30
- System Timers 31
- Setting Modes 34
- Do System Print 34
- Remote Reset Algorithm 35
- Configuration 35
- Goto User Menu 1 37
- View Location Text (LCD Only) 38
- Relearn Hardware 38
- View Circuits 40
- Set System Time 40
- Set System Date 40
- Change Passcode 40
- Chime Circuits 41
- Alter 24Hr Group 41
- Print System Log 41
- Configure Wards 41
- Log Event Codes 42
- View System Log 42
- StarburstLCD 44
- Menu Contents 45
- Time Switches Flowchart 46
- Part Set Group Operation 47
- Code Set Group Operation 47
- Reset Message 48
- Banner Message 48
- Location Text 49
- Printer Header 49
- Part Set Banner 49
- Current Consumption 49
- View Inactive Circuits 50
- Custom Outputs A & B 51
- Modem Options (LCD Only) 52
- Program Digi Flowchart 53
- Reset Digicom 54
- Point ID Extended Reporting 55
- Workshop Canteen 59
- Service Department 59
- Key Point Application Example 60
- Text Editing Keys 62
- Setup New Users 63
- Setup New Users Flowchart 64
- 496487 Issue 3 68
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Menvier Security TS900+
(16 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 1.267 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce