Menvier Security TS900+ Specifikace Strana 22
- Strana / 68
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Installing a Monitored Power Supply
The TS790/TS900 can be configured to monitor the
519XB power supply unit using the 519FM fault
monitor PCB. The 519FM plugs directly onto the
519XB PCB plug labelled JP1.
The 519FM PCB monitors any combination of:
l
Supply Failure (mains)
l
Low Battery Voltage
l
12V Failure (fuse failure)
In order to monitor the above fault conditions, the
outputs on the 519FM must be connected to a
detection circuit.
If required, the PSU battery can be “load tested”
periodically by connecting a switched +ve output
to the 519FM BATT TEST terminal. The battery test
occurs every hour on the hour for one minute, if
during this time the battery voltage drops below
10.6V a “Battery Fault” indication will be
generated.
Pre Power-Up Checks
Once the system is installed, but prior to
powering-up give the system one final check to
ensure that:
1. The wiring conforms to the requirements
detailed in this manual and that all
interconnections are correct (A to A, B to B
etc.).
2. All system cables are kept clear of mains
supply cables, telephone cables and R.F.
cables. It is recommended that cable ties be
used to keep cables separated.
3. Verify that maximum cable lengths and
resistances are not exceeded.
4. Mains power supply cables to the system are
connected to an un-switched fused spur.
5. Grommets are used where cables enter metal
housings to ensure that insulation is not
compromised.
Initial Power-Up
To power the system for the first time:
1. Place a small screwdriver blade between the
pins on the control panel PCB, marked
“FACTORY RESET”. This will ensure the factory
default parameters are set, see page 19.
2. Switch on the 240V mains supply and remove
the screwdriver blade.
3. Check that the power LED on the control panel
PCB is illuminated.
4. Check that the LED remote keypads display
“LT” (Panel Lid tamper) and LCD remote
keypads display “Panel Lid tamper”. The
remote keypad sounders and extension
loudspeakers will operate.
5. Enter the engineers passcode (default 1234)
to silence the sounders.
6. Connect the standby battery.
18
System Installation TS790 & TS900 Installation Manual
PSU. Power
PSU. Batt
PSU. Fuse
Supply
Fail
Battery
Low
12V
Fail
Batt Test
0V
Aux 0V
O/P
A+
TC
TB
TA
ZC
ZB
ZA
CIRCUIT C
CIRCUIT B
CIRCUIT A
Battery Test (045)
Program As:-
NODE
519 FM
Figure 24 519FM Connections
- TS790 & TS900 1
- Overview 3
- System Installation 3
- Engineer’s Menu 1 3
- Engineer's Menu 2 3
- Engineers Menu 3 4
- Appendices 4
- System Architecture 5
- Control Panel 5
- Remote Keypads 6
- TS900 NODE 6
- ID Node (TS900.IDNODE) 6
- TS700 LEC 6
- Specifications 6
- Cable Routing 7
- Remote Network Wiring 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- NETLCD Remote Keypad 12
- NETSTAR Remote Keypad 12
- NETLED Remote Keypad 12
- NETARM Remote Arming Station 12
- PCB Layouts & Connections 12
- Tamper Switch 13
- ENT Key Disable 13
- Engineer’s Keypad 14
- Figure 11. TS900 Node Layout 15
- TS700 LEC Installation 16
- Wiring Detection Circuits 16
- External Sounder Connections 17
- Auxiliary Tamper 18
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 19
- Plug-on Digicom Installation 19
- Connecting a Printer 20
- Programmable Outputs 21
- Pre Power-Up Checks 22
- Initial Power-Up 22
- Power-Up Checks 23
- NVM Defaults 23
- Introduction 25
- Panel Outputs 26
- Digicom Outputs 26
- Digicom Channels 26
- Programmable Output Types 26
- Program Circuits 29
- Circuit Attributes 30
- System Timers 31
- Setting Modes 34
- Do System Print 34
- Remote Reset Algorithm 35
- Configuration 35
- Goto User Menu 1 37
- View Location Text (LCD Only) 38
- Relearn Hardware 38
- View Circuits 40
- Set System Time 40
- Set System Date 40
- Change Passcode 40
- Chime Circuits 41
- Alter 24Hr Group 41
- Print System Log 41
- Configure Wards 41
- Log Event Codes 42
- View System Log 42
- StarburstLCD 44
- Menu Contents 45
- Time Switches Flowchart 46
- Part Set Group Operation 47
- Code Set Group Operation 47
- Reset Message 48
- Banner Message 48
- Location Text 49
- Printer Header 49
- Part Set Banner 49
- Current Consumption 49
- View Inactive Circuits 50
- Custom Outputs A & B 51
- Modem Options (LCD Only) 52
- Program Digi Flowchart 53
- Reset Digicom 54
- Point ID Extended Reporting 55
- Workshop Canteen 59
- Service Department 59
- Key Point Application Example 60
- Text Editing Keys 62
- Setup New Users 63
- Setup New Users Flowchart 64
- 496487 Issue 3 68
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Menvier Security TS900+
(16 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce