Menvier Security TS900+ Specifikace stáhnout pdf (Strana 35)

Remote Reset Algorithm

When the system is programmed for “Engineer

Reset” the requirement to send an engineer to site

can be overridden by the user by using the

“Remote Reset” facility. If an alarm is generated

the system will respond with a four digit “seed”

code which the user quotes to the Alarm

Receiving Centre or alarm company. The “seed”

code is then entered into a decoder and a unique

“Remote Reset” code is generated. This is passed

back to the user and on entering the “Remote

Reset” code, the system is reset.

The “Remote Reset” code is generated using an

algorithm identified by a 3 digit number.

Alternative algorithms can be selected but these

must correspond to that used by the ARC (or alarm

company) otherwise the “Remote Reset” code will

be incorrect. (Default = 004)

Configuration

The configuration options are as follows:

00 Bell Is an SAB

When programmed as “Yes” the control panel

bell output applies 0V when active. When

programmed as “No” the control panel bell

output removes 0V when active. (Default =

Yes)

01 User 1 Limited

When programmed as “Yes” user 1 is disabled

from options 6 and 8 in user menu 2 , and all

options in user menu 3. When programmed as

“No” user 1 has access to all user menus and

options. (Default = No)

02 Fire Signals all

When programmed as “Yes” fire alarm

activations are signalled to the ARC at all

times. When programmed as “No” fire alarm

activations are signalled to the ARC only when

the system is full set. (Default = Yes)

03 Silent 24hr Circuits

When programmed as “Yes” 24hr circuit are

silent. When programmed as “No” 24hr circuits

are audible. (Default = No)

04 Enable Duress

When programmed as “Yes” the reversal of the

first two digits on any passcode will generate a

duress alarm. When programmed as “No” the

reversal of the first two digits on any passcode

will NOT generate a duress alarm. (Default =

No)

05 PA Silent

When programmed as “Yes” PA’s activated by

pressing keys 1& 3 on the remote keypad will

be silent. When programmed as “No” PA’s

activated by pressing keys!&3ontheremote

keypad will be audible. (Default = Yes)

06 Set with Line Fault

When programmed as “Yes” the system can

be set with a telephone line fault, however the

user will be asked to confirm this at the time of

setting. When programmed as “No” the system

cannot be set with a telephone line fault.

(Default = Yes)

07 User Reset

When programmed as “Yes" alarms can be

reset by the user. When programmed as ”No"

alarms can only be reset by the engineer or via

remote reset. (Default = Yes)

08 Tamper Engineer Reset

When programmed as “No" the user can reset

daytime tamper alarms. When programmed

as ”Yes" only the engineer can reset daytime

tamper alarms. (Default = Yes)

09 High Security Engineer

When programmed as “Yes" the engineer

must enter his passcode and remote reset

number to gain access to engineer's menu 1.

When programmed as ”No" only the

engineer's passcode is required to access

engineer's menu 1. (Default = No)

31

TS790 & TS900 Installation Manual Engineer’s Menu 1

Remote Reset

Algorithm > 004

Remote Reset

Algorithm > 010

Engineers menu 1

Select Option :-

Algorithm No.

8

Enter new No.

e.g. 010

ENT

StarburstLCD

LED

E1 -

ENGR 1 -

004

004

010

010

Remote Reset Algorithm Flowchart

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 67 68

Komentáře k této Příručce

Žádné komentáře